How to Change a Car Engine
Changing a car engine is one of the more difficult tasks a home mechanic may ever face. Replacing the engine requires different approaches for every year, make and model, so it’s important to utilize a service manual specific to your vehicle when taking on such a big project. While the process may be different from vehicle to vehicle, some elements of an engine swap are fairly universal and this can be considered a basic outline of the procedures required.
Removing the Old Engine
Remove the hood.While most projects done “under the hood” can be done beneath a hood that’s still in place, removing the engine from your vehicle is likely not one of them. The hood may interfere with your ability to access connections or bolts and will cause problems if you lift the engine out of the engine bay using a cherry picker or engine hoist. The hood will be held in place by hinges on either side, each with two or three bolts. You and a friend will need to support the weight of the hood as you each remove the bolts connecting the hood to the hinges. Once the bolts have been removed, lift the hood off of the vehicle.
- Removing the hood is a two-person job, as one person will have to lift each end.
- Screw the bolts back into the hood to avoid losing them once they are removed.
- Place the hood someplace safe, with cloth pads at each point it may come into the contact with the ground to avoid damaging the paint.
Drain all fluids from the engine.An engine uses a number of different fluids in regular use and all of it will need to be drained prior to removing the engine. Start with the engine oil, which can be drained through the oil drain plug on the oil pan. The coolant can be drained from the radiator petcock, though it’s important to note that there will still be coolant throughout the system as you disconnect coolant lines. The washer fluid reservoir is likely attached to the body of the vehicle, rather than the engine, and can be left alone.
- The fluids drained from your vehicle cannot be re-used in the new engine.
- Drain engine oil and coolant into separate containers for later recycling.
- You can bring oil and coolant to many auto parts stores to be recycled for free.
Disconnect the intake, exhaust and coolant lines.The intake draws air into your engine and looks like a pipe or tube traveling from the air filter to the throttle body. Disconnect the pipe from the throttle body, then remove all the fasteners holding the intake in place and remove it from the engine bay. You may or may not need to remove the radiator in order to remove the old engine, but you will certainly need to disconnect the coolant lines traveling from the radiator to the old engine. The exhaust can be unbolted at the bottom of the exhaust manifold.
- Expect coolant lines to drip or pour coolant as they are disconnected, so place a container beneath each as you disconnect them.
- Refer to your vehicle’s service manual to ensure you have located and disconnected all necessary coolant lines.
- Remember that removing the exhaust bolts can be extremely difficult. Spray the bolts with WD40 and use a breaker bar to remove them, but be careful not to break the bolts.
Disconnect the wiring.Depending on the era of your vehicle, there is a wide variety of wiring possibilities that you may need to address when conducting an engine swap. The more modern the vehicle, the more wiring and sensors you’ll often have to contend with when disconnecting the engine. Be careful not to damage the connectors as you pull them apart, as they are usually made of plastic that can become brittle.
- Refer to a service manual specific to your vehicle’s year, make and model to ensure you disconnect all of the appropriate connections.
- Older, carbureted motors may have fairly few wired connections to contend with, while brand new cars often have many electrical connections.
Unbolt the engine from the transmission.Depending on how the engine is mounted in the vehicle’s engine bay, the transmission may either be behind or to the side of the engine. The bell housing of the transmission fits into place at the back of the engine, or opposite where you will find the serpentine or drive belt. Remove all of the bolts that pass through the bell housing of the transmission and into the engine block. Place a transmission jack below the transmission to support its weight once it is no longer connected to the engine.
- Be very careful not to strip the bolts that connect the transmission to the engine block, as it will be very difficult to drill and tap out bolts with broken heads.
- Do not remove the bolts one at a time. Instead, loosen each of them a bit at a time until they are all hand loose before removing them.
Disconnect the motor mount bolts.The engine in your vehicle is likely connected by three motor mounts, with the fourth serving as the transmission mount. These motor mounts are usually made up of steel and rubber (to absorb engine vibration) with a single bolt passing through the mount to secure the engine. You will need to use a wrench on one end of the motor mount bolt to hold it in place as you use another wrench to loosen and remove the nut from the other side. If you are using a cherry picker to lift the engine out of the engine bay, use your vehicle’s service manual to locate the points to bolt the chain to the engine without doing any damage, and put the chains in place as you remove the motor mounts.
- If you intend to lower the engine out of the bottom of the vehicle, you will likely need to remove a cross member and place an engine jack beneath the engine.
- With the motor mount bolts removed, the engine will now be supported by the cherry picker or engine jack.
Either raise or lower the engine from the engine bay.Depending on the design of your vehicle, it may be easier to raise the engine out of the engine bay using a cherry picker, or to leave the engine where it is and raise the vehicle itself over it. If you are using a professional lift, raising the vehicle above the engine is fairly straightforward, but most home mechanics may struggle to lift the vehicle above the engine.
- Have a friend jack the engine up using the cherry picker, as you carefully guide the engine to ensure it doesn’t begin to swing dangerously.
- Allowing the engine to swing around could cause damage to the engine or your vehicle and can easily injure you.
- Be extremely careful not to get a finger or hand pinched between a swinging engine and the engine bay, as most engines weigh hundreds of pounds.
Installing the New Engine
Locate a good replacement.There are two primary methods of locating a replacement engine: new or rebuilt motors or motors from donor cars. New and rebuilt motors can be purchased from a number of online retailers. Brand new motors are commonly called “crate” motors and offer the reliability of a brand new engine. Rebuilt or refurbished motors were removed from donor cars and disassembled to identify any issues, then reassembled with new gaskets. Both new and rebuilt motors are reliable, and both can often be bought with a warranty. Donor engines are often the least expensive, as they are simply removed from another car and placed into yours.
- Donor engines can sometimes be extremely easy to install, especially if both your vehicle and the donor vehicle are at your garage.
- Crate motors are the most expensive, but offer the highest level of reliability.
- Rebuilt and refurbished motors tend to cost slightly less, but are still considered quite reliable.
Visually inspect the new engine compared to the old.Before installing the new engine, compare it to the one you just removed to ensure they match. Because the same vehicle may have come with multiple engines in the same model year and there may be dozens of variations over the years, it’s important to verify the new engine will bolt in exactly as the old one did. Look for the placement of the accessories (like power steering, alternator and air conditioning) as well as the location of the intake and exhaust manifolds and motor mount brackets.
- If the new engine is missing any accessory components like power steering, it may be easier to remove it from the old engine and install it on the new one before it is placed into the engine bay.
- Engine blocks often have engine codes cast into them. If you locate the engine code, refer it to your vehicle’s service manual to ensure it is the proper engine for the vehicle.
Either lower or raise the new engine into the engine bay.Place the new engine in the engine bay using the same method you used to remove the old one. If you are lowering the engine into place, have a friend slowly and carefully release the pressure in the cherry picker as you guide the engine into place. Take great care to slide the engine into place over the input shaft of the transmission without damaging it.
- The engine may want to twist in the chains as it is lowered by a cherry picker, so be careful to keep the engine aligned properly.
- Do not release all of the tension in the cherry picker once the engine is in place.
- If you lower the vehicle down over the engine, take great care to ensure it is lined up properly to avoid doing damage to the body of the vehicle or the engine.
Bolt the engine in place using the motor mounts.With the engine in place, slide the motor mount bolts through the motor mounts and secure them using two wrenches. Make sure to have all three motor mounts connected and tight before releasing the tension on the cherry picker and allowing the car to support the weight of the engine.
- Before connecting the new motor mounts, inspect them for damage. If the rubber bushings are cracked or damaged, you should replace them before installing the new engine.
- Reduce the pressure on the cherry picker slowly to ensure the motor mounts will support the weight of the engine.
Connect the engine to the transmission.Using the same bolts you removed from the bell housing of the transmission, connect the new engine to the old transmission. Make sure the transmission’s bell housing slides into place and is flush against the engine block and is not at any kind of an angle as you tighten the bolts.
- Refer to your vehicle’s service manual to find out the specific torque specifications required for the bolts connecting your transmission to the engine.
- You may need to use a torque wrench to ensure you place the proper force into tightening these bolts.
Connecting the New Engine
Connect the engine wiring harness.Depending on the make, year, and model of your vehicle, connecting the engine wiring harness may be a fairly simple or an incredibly complex endeavor. If the new engine and the old are exactly the same, it will simplify the process of locating and connecting each of the necessary wires, sensors and connections.
- New model vehicles have far more wiring to contend with.
- Failing to connect the wiring harness properly can prevent the engine from running, make it run poorly, or affect the interior operations of the vehicle such as the gauge’s operation.
Run all the necessary connections.Reconnect the coolant lines and all other connections you had to separate when removing the old engine. If you needed to remove components from your old engine to install on your new one, such as the intake manifold or fuel rail, be sure to connect these as well. Use your vehicle’s service manual to locate and connect all coolant, vacuum, and fuel lines that must be present to make your vehicle run properly.
- This is likely the most time consuming step in the process, as there are a number of connections to address.
- Clearances should not be an issue with a replacement motor when running the connections.
Install the intake.Reinstall the intake, connecting it to the air filter and mass airflow sensor (if equipped) on one end and the throttle body on the other. Many intakes are supported by mounting brackets that will also need to be secured.
- There should be at least one vacuum line connecting to your intake from the cylinder head, but some vehicles may have others.
- There should be no open nipples or nozzles on the intake anywhere once installed.
Connect the coolant lines.Reconnect the coolant lines to the radiator in the same way you removed them. Many coolant lines will require a hand wrench or phillip’s head screw driver to tighten over their respective pipes. Make sure all connections are tight, but be careful not to overtighten them and crack the plastic piping.
- If any of the hose clamps used on the coolant lines seem unusable, you can purchase replacement ones at most auto parts stores.
Look over your work for what you’ve missed.An engine needs air, fuel and spark to run, so start by making sure the intake, fuel lines and electrical system are all installed and intact. Then start running through the rest of the connections you’ve made, ensuring each is tight and in its proper place. Refer to your vehicle’s service manual regularly as you compare its diagrams to what you see in your engine bay to be sure everything has been installed properly.
- If you see an issue, it may be daunting to take things back apart to address it, but starting the engine with something connected poorly or incorrectly can cause serious damage to your new engine.
- You may want to ask a friend to look things over as well, in case they notice something you’ve missed.
Add oil and coolant.With everything in place, refill your radiator with a 50/50 water and coolant mix and add the appropriate amount of oil to the engine. Refer to your vehicle’s service manual for fluid capacities and ensure you meet them.
- With everything connected and the fluids refilled, the vehicle should be ready to run.
- Turn the car over without letting it start a few times (by turning the key as though you want to start it, and then back quickly) to prime the fuel pump and being pumping oil through the engine before starting it for the first time.
Break in new and rebuilt motors.New internal engine components must wear together under certain conditions before they can perform their best. This is referred to as "breaking them in." Start by driving the car at varying speeds for the first two hundred or so miles. Then, take a few medium throttle accelerations up to around 4,500 RPMs and allow the engine to cool completely. Repeat this with heavy throttle a few times, and allow it to cool again. Then change the oil. Drive the car for another 500 miles regularly, without exceeding the red line for your vehicle to finish the break in.
- Properly breaking in a motor can prolong its life and ensure it performs properly.
- Do not drive the vehicle aggressively until after you've broken it in for 500-700 miles.
QuestionShould the cam sensor be replaced when installing new engine?wikiHow ContributorCommunity AnswerThat depends on where you purchased the new engine from. If you purchased a complete motor from the manufacturer, you shouldn't need to replace anything. If you purchase an engine from a donor car, you should plan to address any issues that you may be carrying over from the previous vehicle.Thanks!
QuestionCan a gearbox be damaged when changing a car engine?wikiHow ContributorCommunity AnswerYes - and very easily. You must make sure once you disconnect it from the engine, it is supported and completely disconnected when the engine is removed.Thanks!
QuestionCan I swap engines between a 2008 Hyundai Veracruz GLS and a 2006 Honda Odyssey EX-L?wikiHow ContributorCommunity AnswerTo determine if the engines are compatible, look where all the motor mounts and transmission mounts are, measure the height and width of the Veracruz engine and the Odyssey engine and compare. You also need to swap the computer as well.Thanks!
QuestionHow long does it take to remove and reinstall an engine?wikiHow ContributorCommunity AnswerIt depends upon how familiar you or your mechanic/shop is with the car itself. At minimum, it would take at least 90 minutes. If you've never tried this before and don't have anyone with experience to guide you through the process, it could take you all day or even longer.Thanks!
QuestionI have no experience, but I am mechanically inclined. Could I do an engine swap?wikiHow ContributorCommunity AnswerIf you prepare yourself with all the tools, parts, a manual and you have a lot of patience, it is possible. You may also need to look at online forums or ask for advice from a professional if you get stuck.Thanks!
QuestionIf I change my truck to a diesel engine, do I need to change the transmission?wikiHow ContributorCommunity AnswerIn most cases, yes it should also be changed.Thanks!
QuestionDo I drain oil from an engine?wikiHow ContributorCommunity AnswerGenerally, you should drain the oil. If the company you bought your engine from charges a core, the don't want any fluids in the engine. Some remanufactured engines you can buy don't have an oil pan preinstalled, so you would need to drain it.Thanks!
QuestionHow do I determine if the new engine will be an acceptable replacement for the old one?wikiHow ContributorCommunity AnswerAsk the dealership or speak to a mechanic or possibly a parts person.Thanks!
QuestionAre there any services that will swap engines for me, or do I need to do it myself?wikiHow ContributorCommunity AnswerMost automotive shops will do it for a price, but it depends on the exact shop you visit.Thanks!
QuestionIf I have a 95 Honda Civic, can I swap the motor with a V6 or V8 engine?wikiHow ContributorCommunity AnswerThere might not be enough space, and you would almost certainly need a new transmission (and drivetrain upgrades). It would be extremely difficult, but possible.Thanks!
My 5 yr old engine was replaced due to a recall. Now my AC is not working properly. Is this coincidence or could something not have been connected correctly?
Apart from a VIN report, is there another way to know if an engine came from a manual or automatic car?
I think I was sent an engine from an automatic instead of a manual car. Can I still use it? The crank at the end is different.
Can I put a ls9 in my 1987 rodmaster wagon?
How to know the engine is aligned properly or not?
Sources and Citations
In other languages:
Español: , Deutsch: , Português: , Italiano: , Русский: , Français:
Video: How to Replace an Engine in Your Car (Swap)
Supercut Celebrates The Sexiest Film Scenes In Movie History
10 Things That Change When Youre Finally In The Right Relationship
The Dangerous Side of Mania
Breast Cancer the Second Time
Polenta Bake with Butternut Squash
Should You Weigh Yourself Every Day
How to Broast Potatoes
PeTA criticises Sharon Stone
How to Buy a Puppy Online Safely
How to Update DirectX
Emma Thompson regrets not going on that date with Donald Trump
Facebook may be fined up to 1.63 billion by the EU for massive breach